44.7.3. The Role of Policy in the Boot Process

44.7.3. The Role of Policy in the Boot Process

SELinux plays an important role during the early stages of system start-up. Because all processes must be labeled with their correct domain, init performs some essential operations early in the boot process to maintain synchronization between labeling and policy enforcement.

  1. After the kernel has been loaded during the boot process, the initial process is assigned the predefined initial SELinux ID (initial SID)kernel. Initial SIDs are used for bootstrapping before the policy is loaded.

  2. /sbin/init mounts /proc/, and then searches for the selinuxfs file system type. If it is present, that means SELinux is enabled in the kernel.

  3. If init does not find SELinux in the kernel, or if it is disabled via the selinux=0 boot parameter, or if /etc/selinux/config specifies that SELINUX=disabled, the boot process proceeds with a non-SELinux system.

    At the same time, init sets the enforcing status if it is different from the setting in /etc/selinux/config. This happens when a parameter is passed during the boot process. The default mode is permissive until the policy is loaded, then enforcement is set by the configuration file or by the parameters enforcing=0 or enforcing=1.

  4. If SELinux is present, /selinux/ is mounted.

  5. The kernel checks /selinux/policyvers for the supported policy version. init instpects /etc/selinux/config to determine which policy is active, such as the targeted policy, and loads the associated file at $SELINUX_POLICY/policy.<version>.

    If the binary policy is not the version supported by the kernel, init attempts to load the policy file if it is a previous version. This provides backward compatibility with older policy versions.

    If the local settings in /etc/selinux/targeted/booleans are different from those compiled in the policy, init modifies the policy in memory based on the local settings prior to loading the policy into the kernel.

  6. By this stage of the process, the policy is fully loaded into the kernel. The initial SIDs are then mapped to security contexts in the policy. In the case of the targeted policy, the new domain is user_u:system_r:unconfined_t. The kernel can now begin to retrieve security contexts dynamically from the in-kernel security server.

  7. init then re-executes itself so that it can transition to a different domain, if the policy defines it. For the targeted policy, there is no transition defined and init remains in the unconfined_t domain.

  8. At this point, init continues with its normal boot process.

The reason that init re-executes itself is to accommodate stricter SELinux policy controls. The objective of re-execution is to transition to a new domain with its own granular rules. The only way that a process can enter a domain is during execution, which means that such processes are the only entry points into the domains.

For example, if the policy has a specific domain for init, such as init_t, a method is required to change from the initial SID, such as kernel, to the correct runtime domain for init. Because this transition may need to occur, init is coded to re-execute itself after loading the policy.

This init transition occurs if the domain_auto_trans(kernel_t, init_exec_t, <target_domain_t>) rule is present in the policy. This rule states that an automatic transition occurs on anything executing in the kernel_t domain that executes a file of type init_exec_t. When this execution occurs, the new process is assigned the domain <target_domain_t>, using an actual target domain such as init_t.


Note: This documentation is provided {and copyrighted} by Red Hat®, Inc. and is released via the Open Publication License. The copyright holder has added the further requirement that Distribution of substantively modified versions of this document is prohibited without the explicit permission of the copyright holder. The CentOS project redistributes these original works (in their unmodified form) as a reference for CentOS-5 because CentOS-5 is built from publicly available, open source SRPMS. The documentation is unmodified to be compliant with upstream distribution policy. Neither CentOS-5 nor the CentOS Project are in any way affiliated with or sponsored by Red Hat®, Inc.