Search found 12 matches
- 2019/08/16 08:37:32
- Forum: CentOS 7 - Networking Support
- Topic: OpenVPN Client to OpenVPN Server NAT
- Replies: 2
- Views: 2100
Re: OpenVPN Client to OpenVPN Server NAT
Well... I found a site that says to do this: add ovpns1-route to /etc/iproute2/rt_tables then run the following commands: # Populate secondary routing table ip route add default via 192.168.2.1 dev ovpns1 table ovpns-route # Anything with this fwmark will use the secondary routing table ip rule add ...
- 2019/08/15 10:04:40
- Forum: CentOS 7 - Networking Support
- Topic: OpenVPN Client to OpenVPN Server NAT
- Replies: 2
- Views: 2100
Re: OpenVPN Client to OpenVPN Server NAT
I have confirmed that the OpenVPN Server sees the connection with TCPdump, but my client on Site A doesn't respond... So it appears I'm correct on my thinking that the client doesn't know to go back through the VPN to reply to the connection! I assume I need some kinda firewall rule to return the tr...
- 2019/08/15 09:54:05
- Forum: CentOS 7 - Networking Support
- Topic: OpenVPN Client to OpenVPN Server NAT
- Replies: 2
- Views: 2100
OpenVPN Client to OpenVPN Server NAT
Hello. I am wanting to allow someone from Site B's WAN access something on Site A's network. I am not sure how to configure the server Side of OpenVPN to allow this. Example: Site B External IP: 20.0.0.100 Site B Internal Network 10.0.0.1/24 Site A Internal Network 10.2.0.1/24 So, if someone tries t...
- 2019/08/15 09:10:16
- Forum: CentOS 7 - Networking Support
- Topic: Disregard: OpenVPN - Port Blocked client side?
- Replies: 1
- Views: 1492
Re: OpenVPN - Port Blocked client side?
Nevermind! My fault HAHA I forgot we had blocked port 25 on Client side router from getting out
- 2019/08/15 09:01:16
- Forum: CentOS 7 - Networking Support
- Topic: Disregard: OpenVPN - Port Blocked client side?
- Replies: 1
- Views: 1492
Disregard: OpenVPN - Port Blocked client side?
Hello. I have an OpenVPN server on my CentOS 7 machine. Connection works, traffic all worked except for port 25... I have a mail server running on Side A (OpenVPN Server). When someone from Side B (OpenVPN Client) tries to telnet into port 25 to a client on Side A, it fails. Keep in mind, this is an...
- 2019/08/14 08:07:40
- Forum: CentOS 7 - Networking Support
- Topic: SOLVED: dhcrelay - IPv6
- Replies: 1
- Views: 1559
Re: dhcrelay - IPv6
Opps!!!
HAHA! Forgot to configure radvd!!!! My fault!
Solved
HAHA! Forgot to configure radvd!!!! My fault!
Solved
- 2019/08/14 03:03:57
- Forum: CentOS 7 - Networking Support
- Topic: SOLVED: firewalld Multiple WAN IPs 1 interface help
- Replies: 6
- Views: 3853
Re: firewalld Multiple WAN IPs 1 interface help
THANK YOU, THANK YOU, THANK YOU!!!!
All is working on this part now!!!! REALLY APPRECIATE IT!!!!!
All is working on this part now!!!! REALLY APPRECIATE IT!!!!!
- 2019/08/12 21:43:04
- Forum: CentOS 7 - Networking Support
- Topic: SOLVED: firewalld Multiple WAN IPs 1 interface help
- Replies: 6
- Views: 3853
Re: firewalld Multiple WAN IPs 1 interface help
I created a zone: firewall-cmd --permanent --new-zone="[MyNewZoneName]" I tried adding a zone by source using the below command: firewall-cmd --permanent --zone="[MyNewZoneName]" --add-source="[MyExternalIP]/[Mask]" Then added the following rule: firewall-cmd --zone="[MyNewZoneName]" --add-forward-p...
- 2019/08/12 09:12:22
- Forum: CentOS 7 - Networking Support
- Topic: SOLVED: dhcrelay - IPv6
- Replies: 1
- Views: 1559
SOLVED: dhcrelay - IPv6
Hello. I have setup DHCP Relay agent and have an IPv6 DHCP server running on a different system. It appears DHCP Relay is working, however, my clients don't get a gateway for IPv6 address. If I set the Gateway manually on the clients, then IPv6 fully works. How do I get the DHCPRelay agent to broadc...
- 2019/08/12 07:56:49
- Forum: CentOS 7 - Networking Support
- Topic: SOLVED: firewalld Multiple WAN IPs 1 interface help
- Replies: 6
- Views: 3853
Re: firewalld Multiple WAN IPs 1 interface help
Good to know! That does help a little :) But I am not sure then how to use firewalld to open ports based on source IP. I tried creating zones by source IP address, but this didn't work :(. So, if anyone knows how to open firewall based off WAN IP instead of interface, this would be really helpful!